https://www.lozier.com/products/end-caps/end-cap-with-full-height-wing-panels/

End Cap with Full Height Wing Panels

Wall End Display End Cap featuring Full Height Accessory Panels for wings.

End Cap with Full Height Wing Panels

Wall End Display End Cap featuring Full Height Accessory Panels for wings.

How to Order

This End Cap features a combination of Lozier Products.  See below for details.

Wall End Displays

Product Details

Load Rating

  • 600 lbs evenly distributed per deck (13″ – 19″ D)
  • 800 lbs evenly distributed per deck (22 – 25″ D)

 

  • Freestanding End Display
  • Pegboard Front Panel and Martek Back Panel, other Back Panel styles available
  • Order Shelves separately
  • Order Gap Filler to close off the bottom rear when unit is wider than the island width.
  • Actual width of unit equals nominal width plus 2″
  • Accepts Accessory Panels and connectors
  • Stabilizers required and ordered separately for Non-Compliant height to depth Wall End Displays (See Product Safety information for Height to Depth Chart)
View product details

Product Options and Numbers

QTY.
A. Uprite 2
B. Base Bracket (Standard or Heavy Duty) 2
C. Deck (Standard or Heavy Duty) 1
D. Base Front (Open or Closed) 1
E. Top Rail 1
F. Center Rail (2 per section 78H-120H) 1 or 2
G. Bottom Rail 1
H. Splicer Rail (Sections 78H-120H) Use 2 top rails for splicer on 2′ and 30″ wide sections. 1
I. Back Material (1 or 2 per side) See Back Chart
J. Base End Trim (Pair) 1
K. Uprite End Trim 2
Wall End Display

ORDERING INSTRUCTIONS FOR ISLAND SECTIONS 1/4″ BACK MATERIAL


 

 QTY.
A. Uprite (Standard or Heavy Duty) 2
B. Base Set (Standard or Heavy Duty) 1
C. Hardboard Back and Rail Set 2-Sided 1
D. Uprite End Trim 2
    WED SIZES
Depth  Height
48″ 54″ 60″ 66″ 72″ 78″ 84″ 90″ 96″
13″ N/A N/A N/A N/A N/A N/A N/A
16″
N/A N/A N/A N/A
19″ N/A
22″
25″

Full Height Wing to Wall End Display Accessory Panel Connectors

Product Details

  • Accessory Panel Connectors are needed to attach Accessory Panels to Wall or Contoured End Display, End Merchandising Panels and Close Off Panel
  • Order APWF when installing a Full Height Accessory Panel (FHAP) to the Wall End Display; when installing on a T-Leg Wall End Display, order with a Flush Accessory Panel (FAP)
  • A Wall End Display Rail (WEDER) is required, order separately
  • See Installation Instructions for load capacities and limitations


INCLUDES

  • Upper Connector
  • Base Angle
  • Hardware Pack
View product details

Product Options and Numbers

Example Part #:   APWF   06   PLT   CHR

Full Height Wing to Wall End Display Accessory Panel Connectors: APWF

Base Type: 06, LB, TL (FAP Only)

Upper Connector Standard Finish: PLT, Optional Catalog Colors

Lower Connector Standard Finish: CHR, Optional Catalog Colors

Please view Optional Catalog Colors and Contact Product Management for respective multiple finish code.

Suffix Key
06 – 06 Base (8″H)
LB – Low Base (6″H)
TL – T Leg
FAP – Flush Accessory Panel
PLT – Platinum CHR – Charcoal Black

Full Height Accessory Panel

Product Details

  • Full Height version of Flush Accessory Panel (FAP)
  • Panel extends past the Base End Trim or End Deck and rests on the floor with leveling legs
  • Not compatible with T-Leg Wall End Displays
View product details

Product Options and Numbers

Example Part #:   FHAP   60   16   P   M   PLT   PLT   PLT

Full Height Accessory Panel: FHAP

Uprite Height: 42″, 48″, 54″, 60″, 66″, 72″, 78″, 84″, 90″, 96″

Width: 14″, 16″, 18″, 24″, 30″, 36″

Exterior Panel Style: P, M, P2, M2, S, SI, WG, SG, LG, MG

Interior Panel Style (if required): M, M2, Omit if P2 Exterior Panel

Exterior Panel Standard Finish: PLT, Optional Catalog Colors, Optional Catalog Laminates for Slotwall only

Aluminum Insert (if required): ALU (SI only)

Interior Panel Standard Finish (if required): PLT, Optional Catalog Colors, Omit if P2 Exterior Panel

Frame Standard Finish: PLT, Optional Catalog Colors

Suffix Key
P – Pegboard Back
M – Marteck Back
P2 – Single Pegboard Back, painted two sides
M2 – Single Marteck Back, painted two sides
S – Slotwall Back
SI – Slotwall Back with Inserts
WG – 3×3 Wire Grid Back
SG – Slot Grid Back
LG – Louver Grid Back
MG – Multi-Grid Back
PLT – Platinum
ALU – Aluminum

Vertical Sign Channel for Wing Panel

Product Details

Contact your Sales Rep for ordering Information

View product details

Product Options and Numbers

Part #:   CDC410

TL Shelf

Product Details

  • Two position tilt-in Shelf with extended bracket
  • Angular adjustment: flat or 17° downslope
  • Molding accommodates a 1.235″ tag
  • 1/4″ perforations for clip-on accessories
  • Can order with Aluminum Tag Moldings installed or can order Molding for Shelf separately
View product details

Product Options and Numbers

Example Part #:   TL   4   19   N   PLT

 

TL Shelf: TL

Width:  2’, 30″, 3’, 4′

Depth: 7”, 10”, 13″, 15″, 16″, 17″, 19”, 20″, 22″, 25″, 28″, 31″

Molding: N, M13P, M13S, M35P, M35S

Standard Finish:  PLT, Optional Catalog Colors

Finish When Ordering Painted Molding : 34K, Please Contact Product Management for multiple finish codes

Suffix Key
N – No Molding
M13P – M13 Painted Molding
M13S – M13 Satin Molding
M35P – M13 Painted Molding
M35S – M35 Satin Molding
PLT – Platinum
34K – Platinum Body & Platinum Painted Molding
 Shelf Depth    Downslope 
Flat  17°
7″ 300 lbs 300 lbs
10″ – 25″ 500 lbs 250 lbs
28″ & 31″ 400 lbs 200 lbs

Lbs. evenly distributed

DL Shelf

Product Details

  • Three position, drop-in shelf with extended bracket
  • Angular adjustment: flat, 17° or 30° downslope
  • 1/4″ perforations for clip-on accessories
  • Can order with Aluminum Tag Moldings or can order Molding for shelf separately
View product details

Product Options and Numbers

Example Part #:   DL   4   19   N   PLT

 

DL Shelf: DL

Width:  2’, 30″, 3’, 4′

Depth: 7”, 10”, 13″, 15″, 16″, 17″, 19”, 20″, 22″, 25″, 28″, 31″

Molding: N, M13P, M13S, M35P, M35S

Standard Finish:  PLT, Optional Catalog Colors

Finish When Ordering Painted Molding : 34K, Please Contact Product Management for multiple finish codes

Suffix Key
N – No Molding
M13P – M13 Painted Molding
M13S – M13 Satin Molding
M35P – M13 Painted Molding
M35S – M35 Satin Molding
PLT – Platinum
34K – Platinum Body & Platinum Painted Molding
 Shelf Depth    Downslope
Flat  17° 30°
7″ 300 lbs 300 lbs 125 lbs
10″ – 19″
500 lbs 250 lbs 250 lbs
20″ – 25″ 500 lbs 250 lbs 125 lbs
28″ & 31″ 400 lbs 200 lbs 100 lbs

Lbs. evenly distributed.

Need Something Different? Let’s Talk.

Work with our design and engineering teams to create fixtures that meet your needs. We have access to a wide variety of materials, colors and capabilities to bring your vision to life.

Learn more

Lozier is here to help.

Check out the Services section for all the services Lozier has to offer.  Have an idea you want to explore? Our design and engineering teams are ready to help.

Learn more