https://www.lozier.com/products/end-caps/merchandising-panels/merchandise-panels/

Merchandise Panels

Part Number: EMP, FMP, FHMP

Choose the style that fits your merchandising needs: End (EMP), Flush (FMP) and Full Height (FHMP).

Merchandise Panels

Part Number: EMP, FMP, FHMP

Choose the style that fits your merchandising needs: End (EMP), Flush (FMP) and Full Height (FHMP).

Product Details

  • Three styles available: End (EMP), Flush (FMP) and Full Height (FHMP)
  • All frames are slotted to accept most standard Lozier Shelves and Accessories
  • Frames are punched to accept Double Stem Mount Sign Holder Frame (tapered style)
  • Accepts Accessory Panels and Connectors
  • Uprite End Trims not required and can be deleted from Island End
  • See Installation Instructions for load capacities and limitations

When Merchandising Panels are used on a fixture where the first shelving
section behind the Panels is not equipped with Shelves that engage into the
Uprite slots, Top Rail Hold Down Kits (HMA4381) must be installed. Failure to do
this could allow the Top Rail to become disengaged and the fixture to fall over,
causing property damage or personal injury.

How to Order

End Merchandise Panel

Product Details

  • Use on Islands with same sized Base Decks on both sides
  • Top of Panel is 1” above top of Uprite
  • Fits around Uprite for flush fit to Island Gondola
  • When using Pegboard, the two middle columns of exterior peg holes are unusable
  • Compatible with End Deck

Installation Instructions

View product details

Product Options and Numbers

Example Part #:   EMP   60   36   06   P   M   PLT   PLT   PLT


End Merchandise Panel: EMP

Uprite Height: 42”, 48”, 54”, 60”, 66”, 72”, 78”, 84”, 90”, 96”

Width: 24”, 30”, 36”, 48”

Base Type: 06, LB

Exterior Panel Style: P, M, P2, M2

Interior Panel Style (if required): M, M2, Omit if P2 or M2 Exterior Panel

Exterior Panel Standard Finish: PLT, Optional Catalog Colors

Interior Panel Standard Finish (if required): PLT, Optional Catalog Colors, Omit if P2 or M2 Exterior Panel

Frame Standard Finish: PLT, Optional Catalog Colors

Suffix Key
06 – 06 Base (8″H)
LB – Low Base (6″H)
P – Pegboard Back
M – Marteck Back
P2 – Single Pegboard Back, painted two sides
M2 – Single Marteck Back, painted two sides
PLT – Platinum
ALU – Aluminum

Flush Merchandise Panel

Product Details

  • Use on Islands with different sized Base Decks on both sides (accommodates up to a 9” difference)
  • Top of Panel is flush with top of Uprites
  • Hangs on outside of Uprite
  • When using Pegboard, all exterior peg holes are usable
  • Only Merchandise Panel compatible with T-Leg Base
  • Compatible with all Gondola Back options except Open Backs
  • Compatible with End Deck

Installation Instructions

View product details

Product Options and Numbers

Example Part #:   FMP   60   36   06   P   M   PLT   PLT   PLT


Flush Merchandise Panel: FMP

Uprite Height: 42”, 48”, 54”, 60”, 66”, 72”, 78”, 84”, 90”, 96”

Width: 24”, 30”, 36”, 48”

Base Type: 06, LB, TL

Exterior Panel Style: P, M, P2, M2, S, SI, WG, SG, LG, MG

Interior Panel Style (if required): M, M2, Omit if P2 or M2 Exterior Panel

Exterior Panel Standard Finish: PLT, Optional Catalog Colors, Optional Catalog Laminates for Slotwall only

Aluminum Insert (if required): ALU (SI only)

Interior Panel Standard Finish (if required): PLT, Optional Catalog Colors, Omit if P2 or M2 Exterior Panel

Frame Standard Finish: PLT, Optional Catalog Colors

TL Base Standard Finish = Frame Standard Finish
06 and LB Base Angle Standard Finish = CHR (Charcoal).

Suffix Key
06 – 06 Base (8″H)
LB – Low Base (6″H)
TL – T-Leg Base
P – Pegboard Back
M – Marteck Back
P2 – Single Pegboard Back, painted two sides
M2 – Single Marteck Back, painted two sides
S – Slotwall Back
SI – Slotwall Back with Inserts
WG – 3×3 Wire Grid Back
SG – Slot Grid Back
LG – Louver Grid Back
MG – Multi-Grid Back
PLT – Platinum
ALU – Aluminum

Full Height Merchandise Panel

Product Details

  • Full Height version of Flush Merchandising Panel (accommodates up to a 9″ difference)
  • Panel extends past the Base End Trim and rests on the floor with leveling legs
  • Compatible with all Gondola Back options except Open Backs
  • Not compatible with End Deck

Installation Instructions

View product details

Product Options and Numbers

Example Part #:   FHMP   60   36   06   P   M   PLT   PLT   PLT

Full Height Merchandise Panel: FHMP

Uprite Height: 42”, 48”, 54”, 60”, 66”, 72”, 78”, 84”, 90”, 96”

Width: 24”, 30”, 36”, 48”

Base Type: 06, LB

Exterior Panel Style: P, M, P2, M2, S, SI, WG, SG, LG, MG

Interior Panel Style (if required): M, M2, Omit if P2 or M2 Exterior Panel

Exterior Panel Standard Finish: PLT, Optional Catalog Colors, Optional Catalog Laminates for Slotwall only

Aluminum Insert (if required): ALU (SI only)

Interior Panel Standard Finish (if required): PLT, Optional Catalog Colors, Omit if P2 or M2 Exterior Panel

Frame Standard Finish: PLT, Optional Catalog Colors

Suffix Key
06 – 06 Base (8″H)
LB – Low Base (6″H)
P – Pegboard Back
M – Marteck Back
P2 – Single Pegboard Back, painted two sides
M2 – Single Marteck Back, painted two sides
S – Slotwall Back
SI – Slotwall Back with Inserts
WG – 3×3 Wire Grid Back
SG – Slot Grid Back
LG – Louver Grid Back
MG – Multi-Grid Back
PLT – Platinum
ALU – Aluminum

Recently Viewed Products

Need Something Different? Let’s Talk.

Work with our design and engineering teams to create fixtures that meet your needs. We have access to a wide variety of materials, colors and capabilities to bring your vision to life.

Learn more

Ideas and Inspiration at Your Fingertips

Check out the Markets section for examples of our work in various market segments.  Have an idea you want to explore? Our design and engineering teams are ready to help.

Learn more