MenuCube Saver® System
Part Number: CS
Cube Saver® is a medium duty hand stack shelving system that integrates Widespan-style Uprites with Low Profile S-Series storage shelves. The basic components include Uprite Frame, Beams, Shelf Supports, Particleboard Shelves, Low Profile Storage Shelves, and Shelf Clips.
Cube Saver® System
Part Number: CS
Cube Saver® is a medium duty hand stack shelving system that integrates Widespan-style Uprites with Low Profile S-Series storage shelves. The basic components include Uprite Frame, Beams, Shelf Supports, Particleboard Shelves, Low Profile Storage Shelves, and Shelf Clips.
Roll over image to zoom in.
Product Details
- Medium duty hand stack shelving system
- Integrates Widespan Uprites and Beams with Low Profile S-Series Storage Shelving Shelves
- Low profile Storage Shelves require less space and allow extra storage levels
- No hardware needed
- Mix medium to heavy loads with light to medium loads within same section
- Requires Shelf Supports (CSSS) at all Beam levels, or must use Beam Locking Clip (WS1291 or WS9111)
- Welded Uprites provide front-to-back bracing
- Beams provide side-to-side bracing
SIZE INFORMATION
- Clear opening between posts: Nominal Shelf width minus ⅝”
- Length of continuous run is the sum of the nominal unit widths plus 1¼” for each post in run
- Nominal depth is actual depth of unit
- Vertical clearance between Low Profile Storage Shelves is nominal Shelf spacing less ¾”
- Shelves adjust 2″ on centers
- System height of 84″ or less requires two tiers of Beams to brace each unit
- System height 96″ to 120″ requires three tiers of Beams to brace each unit
- First tier must be no more than 48″ above the floor
COMPONENTS
- Uprite Frame
- Beam Shelves
- Shelf Supports
- Particleboard Shelf
- S-Series Shelves
- Shelf Clips
WARNING: Cube Saver Beams are intended to be used with Cube Saver Shelf Supports. If Shelf Supports are not installed then the beams MUST utilize one of two Widespan Multi-Function Beam Locking Clips, WS1291 or WS9111, depending on the beam location. Failure to do this could allow the Beam to become disengaged causing product damage or personal injury.
| LOAD CHART | |
| # of Shelf Supports | Evenly Distributed Load |
| 1 | 700 lbs |
| 2 | 1,600 lbs |
| 3 | 2,400 lbs |
| 4 | 3,000 lbs |
Cube Saver® Uprite Frames
Product Details
- Uprite post slotted on face, allows shelf adjustment of 2″ on center
- Square holes punched on sides of Uprite post for accessories
- Accessory holes punched 6″ on center on face of Uprite aid beam placement
- Each Uprite Includes 1 Top Cap
- Requires one Frame for each section, plus one at end of each run
- One-piece Uprite Frames for 72″ – 120″ (for taller Uprites contact Product Management)
- Welded Footplate for anchoring: 1/2″ hole
- May require Back-to-Back Connectors
- Evenly distributed load of 10,000 lbs (per Uprite Frame at 48″ max. vertical Beam spacing)
Cube Saver® Beam Shelf Assembly
Product Details
- Order two Beam Shelf Assemblies per section, one at top and one on bottom
- If Shelf Supports are not used Beam Locking Clips (WS1291 or WS9111) are required
INCLUDES
- Particleboard Shelf
- 2 Cube Saver® Beams
- Appropriate quantity of Shelf Supports
Cube Saver® Beam
Product Details
Cube Saver® Particleboard Shelf
Product Details
Cube Saver® Shelf Support
Product Details
Cube Saver® Low Profile Storage Shelves
Product Details
- Heavy Duty only
- Reinforced with 1 1/4″D x 3/4″H Galvanized steel channels
- 5/8″ Industrial grade Particleboard Shelf
- Shelf surface is seal coated for durability and stain resistance
- Adjustable in 2″ vertical increments
- Four Shelf Clips included with each Shelf
- Evenly distributed load of 600 lbs per Shelf
Cube Saver® Shelf Clips
Product Details
- Four Clips required per Low Profile Storage Shelf
- Heavy Duty Storage Shelf only
- Locks Shelf into Uprite
- Heavy gauge steel